Plumbing Basics and Installing a Bath.

Installing a bath isn’t exactly brain surgery, but it does need strong plumbing, carpentry, and often, tiling skills. Changing an old bath with a brand-new one is likewise a reasonably hard project. If the old bath is easily accessible, the job can move speedily; if you have to open a wall to eliminate the old bath and position the brand-new bath the task is much harder. The task is within a home handyman’s abilities, although you will need a helper to move out the old bath and set in the brand-new one. Make certain you have qualified yourself for the job and are comfortable trying it. Instead of hiring a professional to take control of a halfway-completed job, it is much better to consider using one before you start. Opportunities are you might need an expert plumbing technician to make tube connections.

This post will help you set up a brand-new bath in your bathroom if you have already purchased a brand-new bath and don’t require to alter the arrangement of your previous water system pipelines.

Your tools and material checklist should comprise of the following:-

  • New Bath
  • Hammer
  • Pipe Wrenches
  • Prybar
  • Shatterproof glass
  • Level
  • Pliers
  • Adjustable Wrench
  • Putty Knife
  • Screwdriver
  • Cold Chisel
  • Measuring tape
  • Pipe Caps

Preparing for the Installation

The supporting frame provided with the bath should be fitted (if needed) according to the manufacturerís instructions.

Next, fit the taps or mixer to the bath. When fitting the tap block, it is very important to make sure that if the tap comes with a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps unit to prevent strain on the bath bath.

Fit the versatile tap adapters to the bottom of the two taps using 2 nuts and olives (often provided with the bath).

Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.

Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you utilize all of the provided washers.

Connect the trap to the bottom of the waste outlet on the bath by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.

The bath should now be ready to be fitted in its final position.

Removing Old Taps

If you require to replace old taps with new ones as a part of your installation, then the first thing you need to do is disconnect the supply of water. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing taps can be rather problematic due to the restricted access that is frequently the case.

Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a fabric ready for the remaining water that will come from the pipelines. Once the supply pipelines have actually been removed, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single taps from turning throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will need to be cleaned up of any old sealing substance.

Prior to proceeding to fit the new taps, compare the pipeline connections on the old taps to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.

Installing the Bath

Using the two wood boards under its feet, place the bath in the required position. The wood boards are useful in evenly spreading out the weight of the bath over the location of the boards instead of focusing all the weight onto four little points.

The next goal is to make sure that the bath is levelled all round. This can be accomplished by checking the spirit level and adjusting the feet on the bath until the level reads level.

To set up taps, fit the bottom of the outermost flexible tap port to the appropriate supply pipe by making a compression join; then do the same for the other tap.

Turn on the water supply and inspect all joints and new pipework for leaks and tighten them if needed. Fill the bath and likewise check the overflow outlet and the regular outlet for leakages.

Finally, fix the bath paneling as described in the manufacturerís instruction manual.

Tiling and sealing around the bath must wait till the bath has been utilised a minimum of once as this will settle it into its last position.

Fitting New Taps

If the tails of the brand-new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and the other end offers a connection to the existent supply pipes.

If you need to fit a monobloc, then you will require lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.

Next, position the tap in the installing hole in the bath/basin guaranteeing that the washers remain in place in between the tap and the sink. Secure the tap in place with the maker supplied backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular tap ports. The previous type should be connected to the tap ends first, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.

Tiling Around the Bath

In the location where the bath meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, causing the water to penetrate the wall in between the bath and the tiling, resulting in issues with wetness and possible leakages to the ceiling listed below.

You can pick from a variety of coloured sealants to blend in your fixtures and fittings. They are offered in tubes and cartridges, and are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly fill the bath with water before sealing, to allow for the movement experienced when the bath remains in usage. The sealant can split fairly early if you do not take into account this movement prior to sealing.

Ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily available on the market. It is recommended to fit the tiles using water-resistant or water resistant adhesive and grout.

Post Sponsored by Resin Drives Peterlee – Do you want a Resin Bound Drive? – We can help you!