Welcome to Problems related to baths and their solutions.
If cleaning is what you are searching for, I think you have found a wrong search. We will however offer clear explanations about bath issues and attempt to enlighten you on the solutions. The above image gives a clear view of a bath issue, which happens to be a common water spill regarding the bath. However, there are quite a number of factors why baths spill. Some are briefly talked on below. Your questions will be attempted in the paragraphs below
Recurring Questions on Bath issues & solutions
I always find water spilling through my roof immediately after bath usage. What can I do about this?
Over the years, this has been the major problem that makes a lot of bath users seek for a plumber, so don’t think you are the only one who has this bath problem. In the event that you notice water getting through the roof soon after utilizing the bath, consult a plumber. But most times, it isn’t much of a severe problem which often sees the inhabitants using the bath soon after the leakage is detected. Most often, the water is leaving the fitting because of a slight looseness of the trap and may barely require a little effort to make it tight again, which often makes the presence of the plumber almost irrelevant. Nevertheless, it is wise to attempt a critical look at the waste to be able to detect the initial reason for the spill.
The silicone which is around the bath easily goes mouldy. How can I stop that?
There are various reasons for the silicone to have gone mould. The major reason is the less expensive nature of the silicone. A silicone not cleaned or not properly cleaned could be another reason. Chances are, the silicone may not be the reason for the mould, but rather, the soap utilized could also be a cause. This is a great article to peruse, on splitting silicone.
Anytime water gets to the overflow level, the bath spills. Could that be an overflow problem?
When you notice leakages when filling your bath beyond the overflow level, then chances are, the overflow is wrongly fitted. There ought not to be leakage of water if there be an overflow situation. To rectify this problem, the overflow plug has to be removed, properly cleaned, then re-siliconed. However, the most appropriate silicone best in this situation is one that can be submerged.
When my bath is filled up, I observe the water draining gradually. What could be the reason?
Your bath drains slowly even when the drain is blocked because the plug is wrongly fitted or there is a bad seal between the in-between the bath and the fitting. To resolve this issue, you will have to remove the waste and do a re-sealing.
I observed the bath chain breaks always. How do I get a good chain to stop this?
Some chains bought from DIY stores are less expensive, and could easily break, especially when carelessly handled. It is best to acquire one that can withstand hard use or wear, which can be ordered from online or could be bought at some real good DIY plumber stores.
Anytime I try to empty the bath, it takes a relatively long time for it to completely get drained. What can I do about this?
If the bath takes a relatively long time to get emptied, then it is most likely that the outlet is filled with hairs which have reduced the outflow of water. Other things could cause this, but here we are dwelling on bath issues and solutions, hence we would love to concentrate on bath related matters. In some instances where your waste refuses to flow normally, then there might be substances in the waste that has obstructed flow of water. It is therefore needful to check and be sure your outlet has a full or at least 1½ inches to enable free-flow of water. Then, it would be wise to use an unblocked sink called buster. Other exceptionally solid products like One Shot would be very okay. However, one must carefully and strictly adhere to the manufacturer’s instruction because of the high-level risk associated with it.
At the point where the bath gets full, there is always an open space between the bath and the silicone. What could be the cause?
In the event that you discover a gap, and the tile gets too expansive and the silicone seeming to part, then it is on account of the bath not been properly installed. Here, be possible to correct this until the bath is completely removed. To solve this problem, you may have need for a supporting wood to bore in the wall, then you prop up the bath as much as is needed. The wood kept beneath the bath edges is what will support the bath. When this is done, it is best to make some adjustments to the legs beneath the bath as would make the bath well balanced.
I noticed my bath has discoloration. How can I deal with this bath issue?
In the event that you observe an exceptionally grimy bath and not able to remove the stains, you would be amazed on how baking powder could restore the color of your bath. Do make use of Baking powder-it works magic on your bath
My bath has a rust spot. How can I remove this?
If it happens that rust spots are found in your bath, it is very important and most timely to quickly consult a bath specialist who will get out the rust-grinds it off and thereafter considers a re-paint. In other cases, however, when such a problem of rust on the bath becomes severe, the specialist may not be able to do much, except that the bath is replaced.
And if you are not sure please contact a professional plumber, there are a lot around, here is a good one in St Albans.
We have some great videos to show you some DIY tips here.